Mold Design & DFM

Heat Staking Boss Design: Why Does the Joint’s Quality Start in the Mold?

septembre 2, 2026
Last updated: 2026-09-04 · 5 min read Heat Staking Boss Design: Why Does the Joint’s Quality Start in the Mold?…
阅读更多 →

How Do You Design Molded Parts for Ultrasonic Welding? — Joints That Melt Right the First Time

septembre 2, 2026
Last updated: 2026-09-04 · 5 min read How Do You Design Molded Parts for Ultrasonic Welding? — Joints That Melt…
阅读更多 →

Where Should the Gate Go? — The DFM Decision That Echoes Through the Whole Part

septembre 2, 2026
Last updated: 2026-09-04 · 5 min read Where Should the Gate Go? — The DFM Decision That Echoes Through the…
阅读更多 →

Why Do Designers Core Out Thick Sections? — Uniform Walls Before Uniform Anything Else

septembre 2, 2026
Last updated: 2026-09-04 · 5 min read Why Do Designers Core Out Thick Sections? — Uniform Walls Before Uniform Anything…
阅读更多 →

Why Do Molded Parts Need Fillets and Corner Radii? — Stress, Flow and Steel

septembre 2, 2026
Last updated: 2026-09-04 · 6 min read How Do You Protect Payment When You Order a Mold Overseas? — Milestones,…
阅读更多 →

Where Do Ejector Pins Go? — Ejection Layout, Witness Marks and the Sticking-Part Fix

septembre 2, 2026
Last updated: 2026-09-04 · 6 min read How Do You Vet a Chinese Mold Factory Before the Deposit? — Evidence…
阅读更多 →

Where Should the Parting Line Go? — How Parting-Line Placement Shapes Appearance, Flash and Tool Cost

septembre 2, 2026
Last updated: 2026-09-04 · 6 min read Does an NDA Protect Your Design When You Send CAD Abroad? — IP…
阅读更多 →

Mold Venting Design — Where Do Vents Go, How Deep Are They, and What Happens When a Cavity Cannot Breathe?

septembre 2, 2026
Working With a China Mold Maker Across Time Zones — How Do You Keep Engineering Communication From Stalling a Mold…
阅读更多 →

Wall Thickness Transitions in Injection Molding — How Much Taper and Radius Do You Need Where a Thick Section Meets a Thin One, and What Defects Does an Abrupt Step Cause?

septembre 2, 2026
Mold Ownership and Tooling Release — Who Owns the Steel When a Mold Sits Inside a Supplier’s Factory, and What…
阅读更多 →

Rib-to-Wall Ratio for Injection Molding — What Is the Correct Ratio, Why Does It Matter, and What Happens When the Rib Is Too Thick or Too Thin?

septembre 2, 2026
Sourcing Injection Molds from China — How Do You Find a Reliable Mold Maker, What Are the Risks, and How…
阅读更多 →

Rib-to-Wall Ratio for Injection Molding — What Is the Correct Ratio, Why Does It Matter, and What Happens When the Rib Is Too Thick or Too Thin?

septembre 2, 2026
Mold Tooling Budget Allocation — How Do You Plan the Total Cost of a New Mold Program, and What Line…
阅读更多 →

Tolerance Stack-Up in Multi-Part Assemblies — How Do You Account for Mold Shrinkage, Process Variation and Assembly Fit When Designing Interlocking Injection Molded Parts?

septembre 2, 2026
Mold Repair Cost Estimation — How Do You Determine What a Mold Repair Will Cost, Who Pays for It, and…
阅读更多 →